top of page

PMC PA25

Polyurethane Foam and Polyurea coatings.

PMC-PA.jpg

Technical specifications

Output:
25 lbs/min@1250 psi (11.36 kg@86.18 bar)
Max Working Pressure:
2,000 psi
Max Hose Length:
94.5 m
Heater Wattage:
7,500 watts Total (Single Heater)
Hose Heating Power:
90 Volts
Max Fluid Temperature:
190 F (87.7 C)
Air Consumption @ 100 psi (6.9 bar):
33 scfm
Main Voltage:
1 x 208-230V, 50/60 Hz
Electrical @ 230V Single Phase:
40A–7,500W heaters
Main Voltage:
3 x 208-230V, 50/60 Hz, 3 x 380V, 50/60 Hz
Dimensions:
71cm x 66cm x 132cm
Weight:
120 kg

Features and characteristics

The new PA-25/PAX-25 Series Air Proportioner from PMC was developed to provide the applicator with an economically priced proportioner that is applicator riendly, very serviceable and designed to meet modern day Spray Foam and Spray Applied Coatings requirements.

Economically Priced: Less expensive than most electric and hydraulic machines on the market today.

Air Driven Proportioner: 7” Heavy duty single piston air motor.

Open Frame Design: Allows the operator full view and easy access to all the critical components of the proportioner along with easy access to the inlet filters.

Lightweight: The aluminum frame and console construction make this a machine that can easily fit in a small trailer.

Individual “A” & “R” Heaters: The individual mass style aluminum heaters provide independent control of “A” and “R” chemical temperatures.

Re-settable Cycle Counter: Manual re-settable cycle counter allows the operator to precisely measure the amount of chemical used per job.

Air Solenoid Safety Shut Off: Shuts off the air supply should an over pressure occur with the pumps or if the emergency stop button is pressed.

Over Temperature Safety Shut Off: Shuts off all power should heater temperature rise above 220 degrees.

State of the Art Reversing Valve: Reverses Pump Direction without the need for electricity.

Digital Automatic Temperature Control: Digital controllers allow the operator to precisely program the set temperature to suit the chemical system being used. Used in concert with the PMC Temperature Sensing Unit (TSU), the PA-25 Series will provide accurate and consistent hose heat to ensure the most effective yield for your product under varying conditions.

Hose Transformer Tap Settings: Standard terminal block tap setting for your particular hose length.

Standard 1:1 ratio proportioning.

شركة يلما للتجارة

تمثل الشركة الشركات المصنعة المشهورة عالميًا لمعدات العزل المائي والمواد الكيميائية وقطع الغيار والخدمات.

نحن نفخر بخدمة منطقة الشرق الأوسط بأكملها وآسيا وأفريقيا بالمواد والآلات والمنتجات المبتكرة ذات الصلة للعزل الحراري والطلاء الواقي وصناعة مكافحة التآكل.

المملكة العربية السعودية

شركة يلما للتجارة

شارع دلم، السلي،
الرياض-14263، المملكة العربية السعودية
الهاتف: +966 11 241 1337
الجوال: 055 0974205 / 050 7882613
معلومات عنا@yelma-seal.com
www.yelma-seal.com

الامارات العربية المتحدة

برايم سيل للمواد العازلة والوقائية ذ.م.م.

صندوق بريد 115563، دبي، الإمارات العربية المتحدة.
الهاتف: +971 43330172 / 3205568
المبيعات@prime-seal.com
www.prime-seal.com

  • آلات مقاومة المياه

  • المواد الكيميائية

  • أشرطة مقاومة للتآكل

  • المواد المانعة للتسرب

  • منتجات السلامة

  • الإضاءة الصناعية

  • معدات الاغلاق

  • مضخات المياه

  • عدادات التدفق      

  • الأجهزة

دعونا نبدأ

هل تريد المزيد من المعلومات؟

تواصل مع أحد ممثلي المبيعات لدينا للحصول على المساعدة بشأن أي استفسارات قد تكون لديك.

هل تحتاج إلى مساعدة في العثور على المنتج المناسب؟

قم بإلقاء نظرة على مجموعة منتجاتنا الكاملة مع جميع الخيارات المتاحة بما في ذلك الكتالوجات الخاصة بكل منتج.

© جميع الحقوق محفوظة لشركة Yelma Seal.

صمم بواسطة Yelma Seal

bottom of page